{"product_id":"ceresit-ct177-mozaic-render-25kg","title":"CERESIT CT177 MOZAIC 25KG 6m2","description":"\u003cp\u003eMosaic render is a ground-level material, and the 25 kg bucket is the pack for a continuous run of it. This is the larger of the two packs in the \u003ca href=\"\/collections\/mosaic-renders\"\u003emosaic render range\u003c\/a\u003e at Renders World, and both carry the same formulation.\u003c\/p\u003e\n\u003ch2 id=\"what-the-25kg-bucket-is-specified-for\"\u003eWhat the 25 kg Bucket Is Specified For — Plinths, Reveals and Entrance Details\u003c\/h2\u003e\n\u003cp\u003eCeresit CT177 mosaic render 25kg is a 1.0–1.6 mm coloured-quartz plaster declared to EN 15824, specified on plinths, reveals and door jambs where a facade collects dirt and knocks at ground level.\u003c\/p\u003e\n\u003cp\u003eThe manufacturer's own application list is narrower and more useful than \"decorative finish\" suggests, and it splits cleanly between outdoor and indoor work.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOutdoors\u003c\/strong\u003e — surfaces that soil quickly: plinths, balustrades, and window and door jambs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndoors\u003c\/strong\u003e — walls exposed to abrasion and dirt, named on the sheet as entrances, corridors and staircases.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOver insulation\u003c\/strong\u003e — as a facade layer inside the Ceresit Ceretherm systems the sheet assesses, which is where the plinth zone of an insulated wall is finished.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBridging fine substrate cracking\u003c\/strong\u003e — the sheet credits the material with bridging hair-like cracks already present in the substrate.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBelow the plinth line\u003c\/strong\u003e, over \u003ca href=\"\/collections\/xps-insulationboards\"\u003eplinth and below-DPC insulation boards\u003c\/a\u003e, where the build-up needs a hard-wearing face at splash height.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"why-a-resin-bound-quartz-finish-at-ground-level\"\u003eWhy a Resin-Bound Quartz Finish Works at Ground Level\u003c\/h2\u003e\n\u003cp\u003eThe construction is the argument: transparent resin binders holding coloured quartz grits, rather than a pigmented film sitting on a mineral coat. Four declared properties follow from that, and each one earns its place at the bottom of a wall.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eImpact resistance, category I under ETAG 004\u003c\/strong\u003e — the classification specified where a surface is within reach, which is exactly the plinth and entrance zone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWater absorption category W3, w ≤ 0.1 kg\/m²·h⁰·⁵\u003c\/strong\u003e under EN 15824, the lowest-absorption band in that standard, so splashback and driven rain stay on the surface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVapour permeability category V2\u003c\/strong\u003e under EN 15824, meaning moisture in the wall keeps a route outward through the finish.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEasy to keep clean and resistant to scrubbing\u003c\/strong\u003e, in the sheet's own terms — a practical advantage where road spray reaches the wall, and the \u003ca href=\"\/blogs\/news\/red-algae-vs-green-algae-render-uk-guide\"\u003eguide to algae growth on render\u003c\/a\u003e covers what to do when a shaded elevation colours up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"ct-177-technical-data\"\u003eCT 177 Technical Data — Declared Values and the Scope of Each\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eProperty\u003c\/th\u003e\n\u003cth\u003eDeclared value\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eGrain size\u003c\/td\u003e\n\u003ctd\u003e1.0–1.6 mm coloured quartz grits\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBase\u003c\/td\u003e\n\u003ctd\u003eAqueous synthetic resin dispersion with coloured mineral fillers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDensity\u003c\/td\u003e\n\u003ctd\u003eapprox. 1.75 kg\/dm³\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAdhesion\u003c\/td\u003e\n\u003ctd\u003e0.6 MPa, EN 15824\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInterlayer adhesion after ageing\u003c\/td\u003e\n\u003ctd\u003e≥ 0.08 MPa, ETAG 004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater absorption\u003c\/td\u003e\n\u003ctd\u003eCategory W3, w ≤ 0.1 kg\/m²·h⁰·⁵, EN 15824\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater absorption after 24 hours\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 0.5 kg\/m², ETAG 004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater vapour permeability\u003c\/td\u003e\n\u003ctd\u003eCategory V2, 0.14 ≤ Sd \u0026lt; 1.4 m, EN 15824\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater vapour, ETAG test\u003c\/td\u003e\n\u003ctd\u003eSd ≤ 1.0 m, ETAG 004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eThermal conductivity\u003c\/td\u003e\n\u003ctd\u003eλ = 0.61 W\/(m·K), EN 15824\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eImpact resistance\u003c\/td\u003e\n\u003ctd\u003eCategory I, ETAG 004\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication temperature\u003c\/td\u003e\n\u003ctd\u003e+10 °C to +25 °C, air and substrate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRelative humidity during work\u003c\/td\u003e\n\u003ctd\u003ebelow 80%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePreliminary drying time\u003c\/td\u003e\n\u003ctd\u003eapprox. 30 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRain resistance\u003c\/td\u003e\n\u003ctd\u003eafter approx. 3 days\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum water addition\u003c\/td\u003e\n\u003ctd\u003e250 ml per 25 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShelf life\u003c\/td\u003e\n\u003ctd\u003e12 months from production, protect from frost\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDeclaration of Performance\u003c\/td\u003e\n\u003ctd\u003eNo. 00469, EN 15824\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eTwo of those rows repay a second look. The \u003cstrong\u003evapour figure appears twice\u003c\/strong\u003e — a V2 class under EN 15824, which is the product's own classification, and a separate Sd ≤ 1.0 m from the ETAG 004 test regime; quote the EN 15824 line when a specifier asks what the render is classified as. The \u003cstrong\u003eλ of 0.61 W\/(m·K)\u003c\/strong\u003e is the conductivity of a decorative layer a couple of millimetres thick, so it belongs in a build-up calculation and never stands as a wall U-value on its own.\u003c\/p\u003e\n\u003cp\u003eAll declared values assume a substrate, ambient and material temperature of \u003cstrong\u003e+23 °C at 50% relative humidity\u003c\/strong\u003e. A cool, damp UK morning slows every timing on that list, which is worth building into the day rather than discovering at four o'clock.\u003c\/p\u003e\n\u003ch2 id=\"how-to-mix-and-apply\"\u003eHow to Mix and Apply CT 177 — Water Cap, Layer Thickness and Wet-on-Wet Working\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eStir the bucket before use\u003c\/strong\u003e with a slow-speed drill and basket mixer to a homogeneous consistency. Over-mixing is a real fault here: the sheet warns that prolonged, intensive stirring discolours the aggregate and aerates the mass.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdd water only if needed, and cap it at 250 ml per 25 kg.\u003c\/strong\u003e Beyond that the sheet states the material becomes unusable, so measure it rather than pouring by eye.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLay it on with a stainless steel trowel\u003c\/strong\u003e at a minimum of 1.5 times the grain thickness, evenly across the panel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWork wet-on-wet and smooth out\u003c\/strong\u003e, keeping one plane going without processing breaks and holding the same consistency throughout.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTape any unavoidable break.\u003c\/strong\u003e Run self-adhesive tape along a defined line, apply, smooth, then pull the tape with the fresh material still on it and restart from that edge.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eTwo prohibitions sit alongside those steps and both are explicit: \u003cstrong\u003edo not sprinkle the plaster with water\u003c\/strong\u003e, and do not rub the surface back once it is smoothed. Trade practice adds one more — keep the trowel passes running in a single direction, because a circular action rearranges 1.0–1.6 mm grits into swirls that low sun will find later.\u003c\/p\u003e\n\u003cp\u003eOn quantities, this page publishes no coverage rate and no bucket count. That is an editorial hold placed on the record rather than a gap in the document, and the reasoning is explained in the ordering section below. The \u003ca href=\"\/blogs\/news\/mosaic-render-for-plinths-uk-guide\"\u003emosaic plinth application guide\u003c\/a\u003e walks the same sequence in site order, including how the priming stage is set up.\u003c\/p\u003e\n\u003ch2 id=\"substrates-priming-and-curing\"\u003eSubstrates, the Priming Sequence and Curing Conditions\u003c\/h2\u003e\n\u003cp\u003eEvery declared substrate reaches CT 177 through a quartz primer, and the sheet is specific about which one and after how long. Ceresit CT 16 is the named quartz primer, stocked here in the \u003ca href=\"\/collections\/primers\"\u003eexterior render primers\u003c\/a\u003e range, and the sheet recommends tinting it close to the mosaic colour so nothing shows through the transparent binder.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSubstrate\u003c\/th\u003e\n\u003cth\u003eAge or condition\u003c\/th\u003e\n\u003cth\u003ePriming\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eCement and cement-lime plaster\u003c\/td\u003e\n\u003ctd\u003eover 28 days\u003c\/td\u003e\n\u003ctd\u003eCT 16 quartz primer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConcrete\u003c\/td\u003e\n\u003ctd\u003eover 3 months, moisture ≤ 4%\u003c\/td\u003e\n\u003ctd\u003eCT 16 quartz primer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMesh-reinforced layers in ZU, CT 85, CT 190 or CT 100\u003c\/td\u003e\n\u003ctd\u003eover 3 days\u003c\/td\u003e\n\u003ctd\u003eCT 16 quartz primer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCT 87 mortar\u003c\/td\u003e\n\u003ctd\u003eover 2 days\u003c\/td\u003e\n\u003ctd\u003eCT 16 quartz primer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAbsorbent substrates\u003c\/td\u003e\n\u003ctd\u003e—\u003c\/td\u003e\n\u003ctd\u003eCT 17, then CT 16 after minimum 2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGypsum, boards and sound paint\u003c\/td\u003e\n\u003ctd\u003eindoors only\u003c\/td\u003e\n\u003ctd\u003eCT 17, then CT 16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThe render goes on only once the CT 16 has dried completely, and the substrate itself must be even, load-bearing, dry, colour-uniform and free of grease, bitumen and dust. Cavities and unevenness are filled beforehand — CT 29 putty is the sheet's suggestion — so the finished plane is set by the preparation rather than by the decorative coat.\u003c\/p\u003e\n\u003cp\u003eThrough the cure, protect the work with netting or tarpaulins until it has fully hardened, and avoid applying to walls in strong sunlight. A milky cast on fresh material is normal and clears as it dries; prolonged water contact can bring it back temporarily until the surface dries again, so three rain-free days after application is the condition to plan for.\u003c\/p\u003e\n\u003ch2 id=\"fire-class-by-ceretherm-system\"\u003eReading the Fire Class Correctly — It Belongs to the System, Not the Bucket\u003c\/h2\u003e\n\u003cp\u003eThe sheet's reaction-to-fire lines are stated per Ceresit Ceretherm system, and they are not a property of the render on its own. Quote them with the system named, or not at all.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eCeretherm system\u003c\/th\u003e\n\u003cth\u003eReaction to fire, EN 13501-1\u003c\/th\u003e\n\u003cth\u003eETA\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVisage\u003c\/td\u003e\n\u003ctd\u003eB-s1,d0\u003c\/td\u003e\n\u003ctd\u003e11\/0395\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePopular\u003c\/td\u003e\n\u003ctd\u003eB-s2,d0\u003c\/td\u003e\n\u003ctd\u003e08\/0309\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eClassic\u003c\/td\u003e\n\u003ctd\u003eB-s2,d0\u003c\/td\u003e\n\u003ctd\u003e09\/0014\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePremium\u003c\/td\u003e\n\u003ctd\u003eB-s2,d0\u003c\/td\u003e\n\u003ctd\u003e08\/0308\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWool Classic\u003c\/td\u003e\n\u003ctd\u003eno class stated on this sheet\u003c\/td\u003e\n\u003ctd\u003e09\/0026\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eThree of the four classified systems sit at \u003cstrong\u003eB-s2,d0\u003c\/strong\u003e, and only Visage is listed at B-s1,d0 — so a specification written against B-s2,d0 holds across the wider set. Wool Classic carries an ETA on the same sheet with no fire line beside it, and Ceretherm Reno appears under a Polish national assessment, ITB-KOT-2018\/0472, likewise without one; neither gap is filled by borrowing a neighbouring system's class. For UK work, reaction to fire is assessed for the wall as built under current Approved Document B guidance, and the render's contribution is one input to that.\u003c\/p\u003e\n\u003ch2 id=\"colour-choice-and-light-reflectance\"\u003eColour Choice and the Light Reflectance Condition\u003c\/h2\u003e\n\u003cp\u003eThe sheet attaches a condition to colour that most mosaic listings leave out, and it explains why this material is a plinth product rather than a whole-elevation one. Ceresit recommends a light reflectance coefficient of \u003cstrong\u003eHBW 20 or above\u003c\/strong\u003e, and directs anyone specifying below that to consult its technical department so the insulation system can be selected to suit.\u003c\/p\u003e\n\u003cp\u003eWith intense dark colours, the sheet limits CT 177 as a facade layer within a Ceretherm system to \u003cstrong\u003esmall areas such as plinths and architectural details\u003c\/strong\u003e. Deep shades on large surfaces are a heat question rather than a colour-fastness one, which the \u003ca href=\"\/blogs\/news\/dark-colours-on-render-solar-heat-risk-uk\"\u003eguide to dark colours and solar heat on render\u003c\/a\u003e sets out, and the \u003ca href=\"\/blogs\/news\/decorative-facades-with-mosaic-render\"\u003edecorative facade guidance\u003c\/a\u003e covers pairing a mosaic plinth with a lighter finish above it.\u003c\/p\u003e\n\u003ch2 id=\"choosing-between-the-two-pack-sizes\"\u003eChoosing Between the 25 kg and 10 kg Buckets\u003c\/h2\u003e\n\u003cp\u003eBoth packs are the same product under the same data sheet and the same Declaration of Performance, so the choice is about how much wall is in front of you and how many part-used buckets you want left over.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003ePack\u003c\/th\u003e\n\u003cth\u003ePractical difference\u003c\/th\u003e\n\u003cth\u003eSuits\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003e25 kg bucket\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFewer batch codes across one plane\u003c\/td\u003e\n\u003ctd\u003eContinuous plinth runs, full elevations\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/ceresit-ct177-mosaic-render\"\u003e10 kg bucket\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eSmaller commitment per colour\u003c\/td\u003e\n\u003ctd\u003eReveals, returns, patch repairs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eOne instruction governs both, and it is the sheet's own: use material from the \u003cstrong\u003esame production batch number on a single plane\u003c\/strong\u003e. That is the practical case for the larger pack wherever an uninterrupted surface is involved.\u003c\/p\u003e\n\u003ch2 id=\"ordering-stock-and-batch\"\u003eOrdering the 25 kg Bucket — Price, Stock and Batch Continuity\u003c\/h2\u003e\n\u003cp\u003eThe Ceresit CT177 mosaic render 25kg bucket is listed at \u003cstrong\u003e£79.00\u003c\/strong\u003e as displayed in August 2026, and the live record currently shows it as \u003cstrong\u003eout of stock\u003c\/strong\u003e. VAT treatment is not shown in that record, so this page states nothing about it; the 10 kg pack and the collection page carry their own live availability.\u003c\/p\u003e\n\u003cp\u003eNo price per square metre appears here, and that is deliberate. The record carries a standing instruction from Renders World not to publish a coverage figure for CT 177 until the operator lifts it, on the reasoning that yield on a mosaic render moves with grain and substrate. Without a published coverage rate there is no honest divisor, so the bucket price stands on its own and the quantity comes off the printed pack or your own measured trial area.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfirm the colour reference and batch\u003c\/strong\u003e when ordering, and buy a single plane's worth together.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrder the CT 16 primer at the same time\u003c\/strong\u003e, tinted towards the aggregate shade — it is a required layer, not an optional extra.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck the working window\u003c\/strong\u003e against +10 °C to +25 °C and three protected days before booking the scaffold.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 id=\"faq-ct-177-compatibility-limits-and-storage\"\u003eFAQ — CT 177 Compatibility, Limits and Storage\u003c\/h2\u003e\n\u003ch3 id=\"faq-primer\"\u003eWhich primer goes under CT 177, and is it optional?\u003c\/h3\u003e\n\u003cp\u003eCeresit CT 16 quartz primer is named for every declared substrate and is not optional. On absorbent substrates the sequence starts with CT 17, then CT 16 after a minimum of two hours, and on interior gypsum or board substrates the same two-stage sequence applies. Tinting the CT 16 close to the aggregate colour keeps the base coat from reading through the transparent binder.\u003c\/p\u003e\n\u003ch3 id=\"faq-quantity\"\u003eHow do I work out how much to order?\u003c\/h3\u003e\n\u003cp\u003eTake the yield printed on the bucket, apply it to your measured area, and add for corners and reveals. This page holds back a published coverage rate under a standing instruction on the record, so the pack itself and your supplier's confirmation are the figures to plan against. For a repeat colour, ordering a single batch for each continuous plane matters as much as the total quantity.\u003c\/p\u003e\n\u003ch3 id=\"faq-cold\"\u003eWhat are the limits for cold or damp conditions?\u003c\/h3\u003e\n\u003cp\u003eAir and substrate both need to sit between +10 °C and +25 °C with relative humidity under 80%, and the surface wants roughly three days of protection before it is rain resistant. Sheeted scaffolding widens the usable season, and the declared timings assume +23 °C at 50% humidity, so allow longer whenever conditions fall short of that.\u003c\/p\u003e\n\u003ch3 id=\"faq-moisture\"\u003eCan it be used in permanently damp locations?\u003c\/h3\u003e\n\u003cp\u003eThe sheet advises against areas exposed to long-lasting moisture and notes that moisture pressure from behind can damage the rendering, so appropriate sealing layers need to be in place first. On a plinth, that means the below-DPC detailing and drainage are resolved before the decorative layer goes on, which is where this material performs at its best.\u003c\/p\u003e\n\u003ch3 id=\"faq-storage\"\u003eHow should buckets be stored?\u003c\/h3\u003e\n\u003cp\u003eUp to 12 months from production in cool conditions and the original undamaged packaging, protected from frost. High temperatures and direct sunlight matter just as much, since the sheet warns that storing or transporting the material hot can start the setting process; reseal any opened bucket tightly and use it up promptly.\u003c\/p\u003e\n\u003ch2 id=\"technical-documentation\"\u003eTechnical Documentation — Ceresit CT 177\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/datasheets.tdx.henkel.com\/CERESIT-CT-177-en_GL.pdf\" rel=\"noopener noreferrer\" target=\"_blank\"\u003eCeresit CT 177 Technical Data Sheet, English global edition (PDF)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"CERESIT","offers":[{"title":"Default Title","offer_id":56417897513335,"sku":null,"price":79.0,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0973\/1375\/1415\/files\/Ceresit-CT177-25kg-MOSAIC-RENDER.webp?v=1767042873","url":"https:\/\/renders-world.co.uk\/products\/ceresit-ct177-mozaic-render-25kg","provider":"Renders World","version":"1.0","type":"link"}